• Condition Monitoring
  • Food and Beverage Industry
  • condition monitoring sensors
  • Condition-Based Monitoring

Condition Monitoring for Food and Beverage Manufacturing

Alex Vedan

Updated Nov 18, 2026

9 min.

Key Points

  • Start condition monitoring with the food and beverage assets that have no standby unit, such as a homogenizer or an ammonia compressor.
  • IP69K-sealed wireless sensors can stay on a mixer or pump through foam and high-pressure rinse cycles.
  • An early alert lets the planner book the repair into the next sanitation window instead of stopping a running line.

Condition monitoring in food and beverage manufacturing means fitting sensors to the machines that stop a line and reading their vibration, ultrasound and temperature through production runs and sanitation cycles. What sets food and beverage plants apart is the setting: daily foam-and-rinse washdown, freezers far below 0°F and changeover windows that leave little time for inspection.

This guide is for the maintenance manager or reliability engineer at a dairy, bakery, sauce, meat or beverage plant. It ranks the assets that most often halt food lines, follows a mixer gearbox through a sanitation cycle and covers refrigeration, audit records and how to scope a first pilot.

What Does Condition Monitoring Do in a Food and Beverage Plant?

It tracks how each critical machine runs, so the maintenance team sees a bearing, gear or seal problem weeks before it halts production and can plan the repair into a sanitation or changeover window. The output is a list of assets that need attention, ranked by how far the fault has progressed.

Route-based checks struggle in food plants because technicians usually reach the equipment during sanitation or a changeover, when the agitator is stopped and the filler is idle. Faults grow under full product load, so a reading taken on a stopped gearbox says little about how it behaves at 3 a.m. with a full batch.

Continuous sensors sample during production. Tractian sensors sample on a 10-minute default interval, which captures the asset under the loads it carries most of the day, and then keep sampling through the washdown that follows.

Which Food and Beverage Assets Stop Lines Most Often?

The assets that most often halt a food or beverage line are the ones without a standby unit: homogenizers, filler drives, mixers and agitators, product and CIP pumps, conveyor gearmotors and the refrigeration compressors behind the cold rooms. Each one fails in its own way, and each sees a different amount of water and chemical during sanitation.

AssetTypical failure modes (general industry examples)Signals that tend to show it firstWashdown and sanitation exposure
HomogenizerPlunger seal and valve seat wear, crankshaft bearing wear, belt and pulley misalignmentVibration at running speed and pulley frequencies, crankcase temperatureExterior hosed down daily; product side cleaned by CIP
Filler and capper driveCarousel gearbox wear, main drive bearing wear, cam follower wearVibration at gear mesh frequency, ultrasound for lubrication lossHeavy washdown inside the filler enclosure, often with foaming or chlorinated cleaners
Mixer and agitator gearboxGear oil contaminated by water, gear tooth wear, output bearing wearUltrasound first, then temperature, then vibrationFoam and hot rinse on the drive housing after each batch or shift
Product and CIP pumpsMechanical seal leaks, cavitation, bearing wearUltrasound and vibration for cavitation, temperature at the bearing housingCaustic and acid CIP solution through the pump; external rinse on motor and coupling
Conveyor gearmotorsShaft misalignment, gear wear, head and tail shaft bearing wearVibration, temperatureFrequent washdown on open belts in raw and cooked areas
Ammonia screw compressorBearing wear, rotor wear, motor winding and insulation faultsVibration and temperature on the compressor; current and voltage on the motor circuitDry machine room; light cleaning
Evaporator and spiral freezer fansUnbalance from ice build-up on blades, bearing wear in sub-zero airVibration, temperatureDefrost water and periodic sanitation of freezer interiors

On a homogenizer, pulley vibration and crankcase temperature carry the early warning, while on a mixer gearbox in a wet area ultrasound usually moves first. Exposure decides the mounting: a sensor on a filler drive has to survive a hot rinse each shift, while one on the ammonia compressor sees an occasional wipe-down.

Washdown Walkthrough: Monitoring a Mixer Gearbox Through Sanitation

A sealed wireless sensor on a mixer gearbox keeps reporting through foam and high-pressure rinse, and the reading that matters often appears in the first production hours after sanitation. A common failure path starts when rinse water gets past a shaft seal or breather and thins the gear oil.

Take the agitator gearbox on a 1,000-gallon batch tank in a sauce plant as an illustrative example. One Smart Trac Ultra sensor goes on that gearbox housing near the output bearing, bonded with adhesive or mounted on a tapped stud in minutes, and measures vibration, ultrasound, temperature and RPM on that one asset. The sensor is IP69K sealed and suited to high-humidity installation, so it stays on through the cleaning cycle.

Stage (illustrative example)What the mixer is doingWhat the sensor picks upWhat the team does
1. Production runAgitator at full speed under a full batch of productBaseline vibration at gear mesh and bearing frequencies; RPM confirms speedNothing yet. Janus, Tractian's industrial AI, learns how the gearbox runs under this load
2. Foam and pre-rinseAgitator stopped, drive housing coated with alkaline foamRPM drops off and the readings describe a stopped gearboxSensor stays mounted, or comes off and goes back on if the sanitation SOP requires bare equipment
3. High-pressure hot rinseWater jets hit the housing, breather and shaft sealSampling continues; a short temperature swing from the rinse water is expectedSanitation crew keeps the jet off the seal and breather where the SOP allows
4. First production hours after restartAgitator back under load with water in the oilUltrasound rises above baseline as the oil film weakens, then bearing temperature creeps upAlert with likely cause and severity; planner books an oil sample and change for the next sanitation window
5. Several weeks with no actionGear and bearing surfaces start to wearVibration at gear mesh frequency growsRepair turns into a gearbox rebuild or replacement, possibly mid-production
6. After the oil change and new sealGearbox running on clean oilUltrasound and temperature settle back to baselinePost-repair trend confirms the fix and closes the finding

The order of signals in stages 4 and 5 is the reason to monitor ultrasound on gearboxes in wet areas. Ultrasound picks up friction and lubrication trouble before wear sets in, while vibration confirms progression once surfaces are damaged. Learn more about food grade lubrication.

A version of this chain played out at Danone. The sensor on a cheese-processing vessel gearbox showed signs of lubrication failure, the analysis pointed to an oil viscosity that was not right for the equipment, and fixing the oil choice spared the plant a new $7,600 gearbox.

Refrigeration and Utilities: Compressors, Fans and Pumps

Refrigeration is often where one failure puts the most product at risk, because a stopped ammonia compressor can warm a cold room or freezer full of finished goods in hours. Utilities such as CIP supply pumps and plant air compressors carry a similar risk, since several lines depend on each one.

An ammonia screw compressor benefits from two kinds of monitoring. A Smart Trac Ultra on the compressor tracks bearing and rotor condition, while Energy Trac is mounted in the electrical panel feeding the compressor motor, without stopping the process, and reads current, voltage and power factor. On that circuit it looks for rotor, stator, winding or insulation faults, plus voltage imbalance.

With multimodal monitoring, Janus combines the mechanical and electrical readings into one view of the compressor's health. Read together, the two layers show whether a fault sits in the compressor bearing or the motor winding before anyone opens the casing, so the team can order the right parts for the next planned stop.

Evaporator fans in blast freezers and spiral freezers are the other common target. Tractian sensors work in cold rooms and cooling tunnels and are rated down to -40°F, so they can watch fan bearings and catch unbalance from ice on the blades between defrost cycles.

Maintenance Records, Food Safety and Audits

Condition monitoring adds a dated history for each monitored asset, covering its condition trend, the alerts raised and the repairs that closed them, which gives the maintenance side of an audit file more to show than a signed PM checklist. Food safety schemes and FSMA inspections look for evidence that equipment is kept in sound, sanitary working order.

Tractian is built for condition monitoring and AI asset health. Tractian easily connects to the CMMS that already holds the plant's work orders, such as MaintainX, Fiix, UpKeep or Limble, plus ERPs like SAP and Oracle NetSuite. Through these integrations, a finding on a CIP pump can become a work order in the existing system, with the alert history attached for the auditor.

The HACCP plan, sanitation SOPs and their verification records stay with the food safety team. Condition data supports them where equipment condition touches a control point, such as a pasteurizer feed pump, a cooling tunnel fan or the CIP supply pump that cleaning validation depends on. Learn more about clean-in-place (CIP).

How to Start: Pilot Line, Criticality and Peak Season

Start with one line and the five to ten assets on it that have no standby, and install six to eight weeks before the plant's busiest season so the models have a baseline before peak load. Tractian begins with an on-site Asset Risk Assessment of criticality, failure modes, operating conditions and business impact, which sets the first scope.

  1. Pick the pilot line. Choose the line whose stops cost the most, often the one feeding the filler or the packaging hall.
  2. Rank its assets by consequence. Score product at risk, repair lead time and failure history for each machine on that line.
  3. Time the install around peak. Holiday baking, summer beverage demand and the spring milk flush each load equipment harder than the rest of the year.
  4. Agree who acts on alerts. Name the planner who books repairs and the sanitation windows the repairs go into.
  5. Review the pilot with numbers. Count confirmed findings, repairs moved into planned windows and downtime hours avoided.

To put a value on each asset, multiply the hours a failure would stop the line by the cost of a stopped hour, then add the costs specific to food:

Cost of one failure = lost production + product disposal + sanitation and restart time + emergency repair premium

A mixer gearbox failure mid-batch, for example, adds a discarded batch and a full re-clean to the repair itself. Dairy plants can also add the cost of diverting raw milk when a line is down during the flush.

How Tractian Supports Food and Beverage Plants

Tractian combines wireless sensors with AI software that reads machine health in real time and tells maintenance teams what is wrong, why and what to do next. In food plants that means sensors built for wet and cold areas and alerts the planner can schedule around sanitation.

  • Wet and cold areas: IP69K sealed, suited to high humidity and rated from -40°F to 250°F.
  • Hazardous areas: Class I Div 1 ATEX/IECEx/NFPA compliant.
  • Install: sensors go on in a day with no cabling or plant Wi-Fi, run on a battery that lasts up to 5 years and reach full visibility within the first 14 days.
  • Diagnosis: each alert states the problem, its severity and the next step, with expert-vetted human review when a finding needs a second look.

At Danone, the vibration profile tied to a homogenizer pulley climbed, a sign of possible misalignment, and the team found the connecting rods and the asset's block already wearing when they inspected it. Left to break down, that homogenizer could have cost as much as $40,000 in maintenance, a stop of 3 to 30 days and commercial impact estimated at $120,000 to $600,000.

Over 112 days, a Unilever food plant prevented 19 failures, protected over $796K in corrective costs and avoided 117 hours of unplanned downtime. One catch was bearing wear on a syrup elevating screw, found through temperature above its limit, which led to new bearings, seal and packing gland and more than $200K in avoided cost.

Frequently Asked Questions

Can vibration sensors stay on through daily washdown?

Sensors with an IP69K rating are built for high-pressure, high-temperature water jets, so they can stay mounted while the sanitation crew foams and rinses a line. Tractian sensors are IP69K sealed and suited to high-humidity areas. If a sanitation SOP calls for bare equipment, the sensors can be removed and reinstalled after cleaning.

Does condition monitoring work in cold rooms and blast freezers?

Yes, provided the sensor is rated for the temperature. Tractian sensors operate from -40°F to 250°F and are designed for cold rooms, cooling tunnels and areas with tight temperature and humidity control. Evaporator fans and freezer conveyor drives are common first assets in those spaces.

Which food and beverage assets should be monitored first?

Begin with the assets that stop a line and have no standby unit, such as the homogenizer, the filler drive, the main mixer gearbox or the ammonia compressor. Then rank the rest by product at risk, repair lead time and how often the asset has failed in the last two years. A pilot on one line usually covers five to ten assets.

Can condition monitoring help with food safety audits?

It can add evidence to the maintenance part of an audit file: a dated record of how an asset ran, what was flagged and what repair followed. It does not replace the HACCP plan, sanitation SOPs or their verification records. Tractian connects to the CMMS that holds work orders, so the findings sit next to the job history auditors already review.

Do food plants need Wi-Fi in the production area for wireless sensors?

Not with sensors that send data over a cellular link. Tractian sensors reach a receiver by radio and the data goes to the cloud over LTE, so the plant Wi-Fi and wiring are not part of the install. That helps in wet areas, freezers and machine rooms where access points are rare.

See How Tractian Would Cover Your Washdown Lines

Bring the asset list for one line, with its homogenizer, filler drive, mixers, pumps and refrigeration, and note which areas see daily washdown. A Tractian specialist will walk through where sensors would mount, which signals to watch on each machine and how alerts would reach the planner. Book a Tractian condition monitoring demo for your food or beverage line.

Alex Vedan
Alex Vedan

Director

Alex Vedan, Marketing Director at Tractian, develops impactful strategies that empower industrial clients across North America and LATAM to achieve operational excellence. By aligning innovation with customer needs, he ensures Tractian solutions drive meaningful improvements in efficiency and reliability.

Share

Start Exploring Tractian Condition Monitoring